Water loss is expected to happen from a swimming pool or a spa at some point when they are in use. Normally, the loss of water from the structure in subject takes place in three main ways, namely, backwashing the filters, evaporation, and splash out. Water loss can be significant to people who stay in arid regions. This is what Queen Creek pool service is all about.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, one should understand that evaporation rates keep on changing depending on what season of the year it is. Also, in case the use of the pool has risen recently, it implies that water loss will increase as well. In case none of these activities have happened in the recent past and yet water loss is happening at a faster rate, one ought to be suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
The other technique one can use to ascertain if there is a leak in the structure is marking the water level in the pool at the skimmer. One can do this using grease, a pencil, or tape. Afterwards, one should leave the structure for a duration of 24 hours before checking on the new level of water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket should be allowed a duration of 24 hours after which it should be checked. If the water in the pool has dropped in level below that of water in the bucket, then it means that a leak exists. Since water in the bucket and in the pool are bot subjected to evaporation, water loss should happen at the same rate.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, one should understand that evaporation rates keep on changing depending on what season of the year it is. Also, in case the use of the pool has risen recently, it implies that water loss will increase as well. In case none of these activities have happened in the recent past and yet water loss is happening at a faster rate, one ought to be suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
The other technique one can use to ascertain if there is a leak in the structure is marking the water level in the pool at the skimmer. One can do this using grease, a pencil, or tape. Afterwards, one should leave the structure for a duration of 24 hours before checking on the new level of water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket should be allowed a duration of 24 hours after which it should be checked. If the water in the pool has dropped in level below that of water in the bucket, then it means that a leak exists. Since water in the bucket and in the pool are bot subjected to evaporation, water loss should happen at the same rate.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
